BARIX Streaming Client Manual do Utilizador

User ManualInstreamer Network audio encoder for commercial, industrial and security applications Firmware V4.01Released 4th May 2011Supports: • INS

3 Device ConfigurationYou can adjust network settings, streaming destinations, monitoring settings and more with the Web interface. To enter the configu

does not have to get a new IP address at power on or reboot.IP AddressEnter the 4 values of the desired static IP address e.g.:• “192.168.0.12” for an

Gateway IP AddressA correct setting of the Gateway IP address is needed to stream to the Internet or to destinations outside your local network (LAN).

Exstreamer 1000 have external Analogue to Digital circuitry which support input speeds of 32 and 48kHz. The selection provides a better input signal t

Encod./Quality 0 1 2 3 4 5 6 7MPEG1 48kHz 88 96 104 120 144 160 176 192MPEG2 16kHz 35 38 44 48 56 64 80 96The above table shows only the average bit r

Own NameYou can enter the name of the Barix Instreamer here. This name will be returned when using the DISCOVER command (see technical documentation).

upon the state of the GPI configured as the Control GPIControl GPI Defines which GPI will control the streaming if the streaming mode is “send on I/O”.

Receiver Port is used.Radio PathEnter a radio path to listen to the transmitted stream of this Barix Instreamer using a device that is able to play MP

Now the TOS bits themselves:• Delay - when set to '1' the packet requests low delay.• Throughout - when set to '1' the packet requ

connection type (except for the types “BRTP” and “SIP” which are only available with the first entry).Stream to Disabled entrySet the connection type t

Table of Contents1Introduction...71.1About the “Instreamer” firmware

Stream to Shoutcast source entrySet the connection type to “Shoutcast source” to connect (TCP) to a single Shoutcast server. Enter IP and port of the

Trap RepeatDefine the SNMP trap repeat interval. The trap is repeated if the audio level values are still out of range.Silence TimeoutDefine the time in

3.5 Control settingsThese settings adjust the control port properties.UDP command portDefines the port where the device will receive commands via UDP.

Baud rateSelect the serial transmission speed from “300” to “115200” Baud (bits per second). Data bitsSelect “7” or “8” data bits. ParitySelect “no”,

3.7 Security settingsThese settings can be used to secure the access to the device on different levels. The status is shown next to each password (set

View configuration password usageWhen the password is set the user clicking on the “Config” button has to type in the password into the password field of

SNMP Community RwriteChoose a password for the Read and Write Community, or "not protected" to ignore both the read and write communities or

4 Reverting to factory defaultsClick the button.Click on the button to enter the defaults page.You will see the following screen:Click on “Factory

5 Rebooting the deviceClick the button.Click on the button to enter the reboot page.You will see the following screen:Click “Reboot the device” to

6 Rebooting the deviceBarix preloads the Instreamer 100 devices with firmware which is current at the day of production. Barix constantly enhances the

Control GPI ...24Active open/closed...

6.3 Web UpdateTo apply the “Web Update” procedure you will need a standard web browser and the IP address of the device (announced by the SonicIP feat

Upon start up the following screen appears. The Bootloader version and date will most likely be different:STEP 6Click on "Browse..." to sele

Click on “Upload” to start the upload process which will take approximately 2 minutes. Warning: If the web update is interrupted during the process (p

Select the file “reboot” and click on the “Open” button and in the following window click the “Upload” button.The following screen appears:STEP 9After

7 DictionaryDHCP Short for Dynamic Host Configuration Protocol, a protocol used to assign an IP address to a device connected to a Network.IP Short for

8 Legal Information© 2012 Barix AG, Zurich, Switzerland.All rights reserved.All information is subject to change without notice. All mentioned tradema

Flow control...35Local port...

1 Introduction1.1 About the “Instreamer ” firmwareThe “Instreamer ” firmware is designed to serve as a versatile, network-enabled analog and digital aud

• Supports IR remote control command relaying (Network to IR out).• Supports Serial Port relaying (Serial gateway over Network)• New V3.17. Supports a

• Updating the Firmware (explaining how to update or how to change from “standard firmware”)• Step by step “How To” (explaining configuration for exte

2 Device Status and ControlTo view the current status and control it using the Web interface you will need:• the IP address announced over the audio o

SENDINGThe LED next to SENDING has the following meaning:GREY for not sending, GREEN for sendingWhen the device is set to “send on CTS” then the follo